|
|
|
This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This equipment has been tested and found to conform to the directives and standards for a Class A Information Technology Equipment TYPE and for the Commercial Light Industrial equipment class.
The VIP-804 "MegaTouch"™ Video with Serial Touch Screen capabilities are available as an Integrated Video Switch with Remote Control, switching one video monitor with touch screen between four PC's.
The "MegaTouch" system consists of the following components:
1. One - Video Switch Unit
2. One - VIP-210 Power Supply.
Note: The "MegaTouch" does not come with VGA or serial extension cables. They may be ordered from Vetra separately (see Accessories ).
There are three main steps to connect the Video Switch:
1. Connect PC's to Switch unit:
a) Connect the Video outputs of the PC's to the Switch using 15 pin HDD15 male/female extension cables. Connect PC#1's video output to the backpanel connector of the Video Switch marked "TO PC1 VIDEO". Connect PC#2's thru PC#4's video outputs to the backpanel connectors of the Video Switch marked "TO PC2 VIDEO" thru "TO PC4 VIDEO".
Connect PC#1's Video A to the
backpanel connector of the Video Switch marked "TO PC1 VIDEO
A" and Video B to connector marked "TO PC1 VIDEO B".
Repeat for PC's #2, #3, and #4.
b) Connect the Touch Screen inputs of the PC's to the Switch
using 9 pin DB9 male/female extension cables. Connect PC#1's touch
screen input to the backpanel connector of the Switch marked "TO
PC1 T.S.". Connect PC#2's thru PC#4's touch screen inputs
to the backpanel connectors of the Switch marked "TO PC2
T.S." thru "TO PC4 T.S.".
Connect PC#1's touch screen inputs
A to the backpanel of the Switch marked "TO PC1 T.S. A"
and input B to the
backpanel connector marked "TO PC1 T.S. B". Repeat for
PC's #2, #3, and #4.
2. Connect a Monitor(s) to the Switch:
a) Connect the VGA monitor to the 15-pin HDD connector on the backpanel of the Video Switch marked "MONITOR IN".
Connect VGA monitor A to the backpanel
connector on the Video switch marked "MONITOR A IN"
and VGA monitor B to the connector marked "MONITOR B IN".
b) Connect the Touch Screen to the 9-pin DB9 connector
on the backpanel of the Switch marked "TOUCH SCREEN IN".
Connect Touch Screen A to the backpanel connector on the Video switch marked "TOUCHSCREEN A IN" and Touch Screen B to the connector marked "TOUCHSCREEN B IN".
3. Connect the Power Supply to the Video Switch:
The Video Switch is powered by
an external wall plug-in supply the VIP-210 (+5Vdc 1A reg. 110
- 240 Vac 50 - 60 Hz).
First plug the power output plug of this external supply into
the mating jack on the backpanel of the Video Switch marked "+5VDC
IN", and only then plug the supply into a suitable AC power
source. Since the Video Switch has no separate power on/off switch,
it is recommended that the power supply be connected to an AC
power source that has a power on/off switch.
OPERATION
1. Power Up Sequence:
The switch derives its power from an external power supply provided with the MegaTouch. When the Video Switch is powered up, observe on the Video Switch that the front panel Led marked "PWR ON" comes on.
2. PC Selection:
a) Front Panel Selection:
b) Remote Control (available on all models): The MegaTouch may also be switched via remote control. A Hex 31 (PC #1), Hex 32 (PC #2), Hex 33 (PC #3), and or Hex 34 (PC #4) sent via RS-232 to pin 2 of the DB-9 connector on the rear panel marked "REMOTE CONTROL" will switch the MegaTouch from PC1 thru PC4. The data format is one start bit, eight data bits, least significant bit first, one stop bit and no parity. The baud rate is 9600. Pin 5 is ground.
SPECIFICATIONS
Mechanical Dimensions
|
|
|
|
|
|
| VIP-804-V-TS |
|
|
|
|
| VIP-804-V-TS-DE |
|
|
|
|
| VIP-804-V2-TS2 |
|
|
|
|
| VIP-804-V2-TS2-DE |
|
|
|
|
Environmental Operating
Temp: 5
to 104 deg. F (-15 - 40 deg. C)
Storage
Temp: -4
to 122 deg. F (-20 - 50 deg. C)
Supported
Hardware Video Monitors: VGA,
SVGA
Maximum
Resolution: up to 1600 x 1200 to 75 Hz
MegaTouch is a trademark of
Vetra Systems Corporation Copyright © 2003 - 2008 by Vetra
Systems Corporation All Rights Reserved
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
275 Marcus Blvd. Ste-J, Hauppauge, NY 11788-2022 USA Toll Free 1.800.537.9296 Tel: 631.434.3185 Fax: 631.434.3516 e-mail: sales@vetra.com |